AUDIOVOX 3100A,4100A,SP85A,CMT410A,BC55A,CTR1900,PT 300/BC55A,CTR1900 NOTES: These are single NAM units that have user programmable MIN & SIDH, See below for user instructions. The ESN prefix is 138 decimal, 8A hex (Toshiba) These units have an excessive number of "security" features, You MUST know the lock code or the "reprograming" code and you may also need an "activation" code. Take care not to program these options unless you're sure the numbers will not be mislaid. There is a "back door" for the PT 300 portable, see end. Audiovox: 516-231-6051/310-926-7758 NAM programing: 1. With the power turned on enter N N N FUNC # 1, where NNN is the three digit lock code. The manufacturers default is 000. If a reprograming code has been entered in step 26 (see below) this code must be used in place of the three digit lock code. If "CODE ?" appears when the phone is powered up then you must enter the 7 digit "Activation Code" before entering programing mode, (see step 30). 2. The # key increments the step number. 3. The * key decrements the step number. 4. STO enters the data for each step. 5. You MAY directly access any step by pressing RCL followed by the step number. 6. FUNC SND completes programing. 7. FUNC CLR exits programing mode. PROGRAMING DATA: STEP# #OF DIGITS/RANGE DESCRIPTION 01 10 DIGITS MIN (AREA CODE & PHONE NUMBER) 02 3 DIGITS LOCK CODE 03 00000 - 32767 SYSTEM ID 04 00 - 15 ACCESS OVERLOAD CLASS 05 00 - 15 GROUP ID (10 FOR USA) 06 0 OR 1 LOCAL USE MARK 07 0 OR 1 MIN MARK 08 0333 OR 0334 INITIAL PAGING CHANNEL 09 0 OR 1 PREFERRED SYSTEM 10 4 DIGITS STATION CLASS MARK 11 8 BINARY DIGITS FUNCTION 1, SEE NOTE 1 BELOW 12 8 BINARY DIGITS FUNCTION 2, SEE NOTE 2 BELOW 13 00 TO 31 HOURS POWER OFF TIMER (CTX 4000 ONLY) 14 000 TO 255 SECS NO CHARGE AIR TIMER DELAY 15 3 DIGITS CALL TIMER RESET CODE 16 - 25 00000 - 99999 SIDH INHIBIT # 1 THRU # 5 26 3 DIGITS NAM PROGRAMING CODE (LEAVE BLANK, SEE ABOVE) 27 - 29 NOT USED FUTURE USE 30 7 DIGITS ACTIVATION CODE (LEAVE BLANK, SEE ABOVE) NOTES: 1. This is an eight digit binary field. 10000000 = CALL TIMER BEEP 01000000 = AUTO LOCK 00100000 = AUTO SYSTEM REDIAL 00010000 = CALL RESTRICTION 00001000 = 32 DIGIT DIALING CAPABILITY 00000100 = AUTO ANSWER 00000010 = AUTO ANSWER FOR DATA 11111000 = ALL OF THE ABOVE 2. As above but options are: 10000000 = HANDS FREE 01000000 = CONTINUOUS DTMF 00100000 = REPERTORY DIALING 00010000 = HORN ALERT 00001000 = ALLOWS 911 CALLING WHEN UNIT IS LOCKED 01101000 = ALL OF THE ABOVE A/B SYSTEM SELECT: FCN 0 4 DISPLAYS CURRENT MODE, FCN 0 0 = PREFERRED/NON-PREFERRED, FCN 0 1 = PREFERRED ONLY, FCN 0 2 = HOME ONLY FCN 0 3 = NON PREFERRED ONLY, USER PROGRAMING OF MIN & SIDH Press CLR followed by the new five digit SIDH and ten digit MIN. Press FUNC 6. The new MIN will be displayed, hold 6 to display the SIDH. "BACK DOOR" FOR PT-300 1. Remove the battery. 2. Remove the small black square access plate at the lower left of the phone. 3. Place a 10k resistor between pins 4 and 5. (Pin 5 is top right, pin 4 is center bottom) 4. Replace battery, power up phone and enter 0 0 0 FUNC # 1. LOCK: Press LOCK. UNLOCK: Enter three digit code. SYSTEM SELECT: F 0 4 shows current mode. F 0 0 = Pref/Non pref, F 0 1 = Pref only, F 0 2 = Home Only, F 0 3 = Non pref only.